Cold shrink tubing is a rubber sleeve that has been stretched over a removable plastic core at the factory. Slide it over the cable, pull out the core, and the tube contracts to grip whatever is underneath. Nothing gets heated, so there is no heat gun, no torch and no risk of scorching nearby insulation. Our cold shrink tube is made from EPDM rubber and cut to 6" lengths in eight diameters.
How to Install Cold Shrink Tubing
Pick the size whose application range covers the outside diameter of your cable, splice or connector (see the size chart below).
Slide the tube over the cable and position it over the area you want to cover.
Pull the loose end of the core strip. The core unwinds in a spiral and the tube shrinks down behind it. You can pull from either end of the tube.
Keep pulling until the whole core is out. The installation is done. There is nothing to cure or heat.
Cold Shrink Tubing Sizes
Size cold shrink by the application range, not by the as-supplied ID. The cable or component OD must fall between the minimum and maximum of the range so the tube grips tightly once the core is removed.
Size
Part #
As-Supplied ID
Application Range (cable OD, inches)
Application Range (mm)
20mm (0.787")
HSCOSH-0787-6in
0.787"
0.30" – 0.59"
7.6 – 15.0 mm
25mm (1")
HSCOSH-100-6in
1.0"
0.39" – 0.79"
9.9 – 20.1 mm
40mm (1-1/2")
HSCOSH-150-6in
1.5"
0.69" – 1.30"
17.5 – 33.0 mm
53mm (2")
HSCOSH-200-6in
2.0"
0.98" – 1.81"
24.9 – 46.0 mm
70mm (2.75")
HSCOSH-275-6in
2.75"
1.26" – 2.48"
32.0 – 63.0 mm
104mm (4.10")
HSCOSH-410-6in
4.1"
1.69" – 3.70"
42.9 – 94.0 mm
125mm (4.92")
HSCOSH-492-6in
4.9"
1.81" – 4.49"
46.0 – 114.0 mm
150mm (5.90")
HSCOSH-590-6in
5.9"
2.17" – 5.31"
55.1 – 134.9 mm
Cold Shrink vs. Heat Shrink
Heat shrink needs a heat source to recover, and is usually the lower-cost choice for small wires on a workbench. Cold shrink needs no heat. It suits larger cables, field work, confined spaces, tower and outdoor installs, and areas where open flame or hot-work permits are a problem. Cold shrink rubber also stays elastic after install, so it keeps a tight grip as cables expand and contract with temperature. Shopping for heat shrink instead? See our 2:1 polyolefin heat shrink tubing.
Typical Applications
Insulating and sealing cable splices and in-line connections
Weatherproofing coax and antenna connectors on telecom and wireless sites
Covering lugs, bus connections and terminations
Jacket repair and cable insulation in outdoor or damp locations
Any job where a heat gun is impractical or not permitted
Cold Shrink Tubing FAQ
Is this silicone or EPDM cold shrink? This tubing is EPDM rubber. EPDM and silicone are the two common cold shrink materials. EPDM is the general-purpose choice for sealing and insulating cable connections.
Does cold shrink need heat or tape? No. Once the core is removed the tube recovers on its own. No heat, mastic or tape is required to install it.
Can cold shrink tubing be removed or reused? It can be removed by carefully slitting it with a knife, but it can't be reused. Once the core is out, the tube cannot be re-expanded.
What length is it? Each piece is 6" (152mm) long before installation.