Adhesive Lined Heat Shrink Tubing 3:1 Ratio

BuyHeatShrink® 3:1 Thin Wall Adhesive Lined Heat Shrink Tubing 

Features:
  • 3:1 Shrink Ratio with melt adhesive inner lining (shrinks to 1/3 its original diameter)
  • Up to 15% longitudinal shrinkage
  • Meets requirements of AMS-DTL-23053/4 (formerly MIL-I-23053/4), Class 3
  • UL224 VW-1 Certified (Jacket only select colors.  Inquire with us for file information)
  • CSA OFT approved
  • Maximum use temperature 135°C
  • Shrink Temperature of 90°C and operating temperature of -55°C to + 110°C
  • Crosses to:Sumitomo W3B2, Raychem ATUM, Alpha FIT-321, 3M EPS-300, CanusaCPA-100 ,LG GSHS-3635W
  • Typical applications include: Insulation, Wire Identification, Wire Bundling, Mechanical Protection, Color Coding, Lightweight Harnessing, Physical/Electrical Protection of Components, Strain Relief, and Solder Insulation.
Diameter Mil Specification #Manufacturer Part #ID Before ShrinkMax ID after shrinkingWall After Shrink(Total)Wall After Shrink(Adhesive) Buy
1/8" AMS-DTL-23053/4-301HS3A-01250.120".040"0.04"0.013"
500 FT/SPOOL$130.00
4 FT/PIECE$2.00
3/16" AMS-DTL-23053/4-0188HS3A-01880.180".060"0.04"0.017"
500 FT/SPOOL$160.00
4 FT/PIECE$2.25
1/4" AMS-DTL-23053/4-302HS3A-0250.240".080"0.04"0.02"
820 FT/SPOOL$256.00
4 FT/PIECE$2.35
3/8" AMS-DTL-23053/4-0375HS3A-03750.360".120"0.05"0.022"
656 FT/SPOOL$295.20
4 FT/PIECE$3.25
1/2" AMS-DTL-23053/4-303HS3A-0500.470".160"0.06"0.027"
656 FT/SPOOL$440.00
4 FT/PIECE$4.25
3/4" AMS-DTL-23053/4-075HS3A-0750.750".250"0.08"0.037"
500 FT/SPOOL$520.00
4 FT/PIECE$5.50
1" AMS-DTL-23053HS3A-1000.940".320"0.087"0.037"
250 FT/SPOOL$418.15
4 FT/PIECE$8.50
1-1/2" AMS-DTL-23053/4-305HS3A-1501.570".440"0.09"0.037"
4 FT/PIECE$15.00

Our versatile 3:1 thin-wall heat shrinkable tubing is also available with an Adhesive, "dual-wall" construction. Dual-wall is made by combining two different materials. The outer wall is Polyolefin heat shrink, and the inner wall is a hot melt adhesive. When exposed to heat (usually a bit lower than the activation temperature of normal heat shrink), the inner layer begins to flow, just like hot melt glue. When the tubing shrinks and cools down, this inner layer forms an adhesion layer between the tubing and the component or wire. This provides a water-tight seal, protecting the connector and/or wire. It also allows the tubing to stick to the substrate, thus the name “adhesive-lined” heat shrink tubing. Use Polyolefin Heat Shrink Tubing for industrial applications, cable repair, intricate electronics protection, and anywhere you need a versatile seal to insulate and secure electrical components. Practical uses for heat shrink include Wire Insulation, Wire Identification, Wire Bundling, Mechanical Protection, Color Coding, Lightweight Harnessing, Strain Relief, and Solder Insulation.

  • Dimensions & Technical Specs
AMS-DTL-23053
Part Number
Size
Nominal Before Shrinking After shrinking
/4-301 HS3A-0125 1/8" 0.120" .040"
/4-0188 HS3A-0188 3/16" 0.180" .060"
/4-302 HS3A-025 1/4" 0.240" .080"
/4-0375 HS3A-0375 3/8" 0.360" .120"
/4-303 HS3A-050 1/2" 0.470" .160"
/4-075 HS3A-075 3/4" 0.750" .250"
/4-304 HS3A-100 1" 0.940" .320"
/4-305 HS3A-150 1 ½" 1.570" .440"
Write Your Own Review
You're reviewing:Adhesive Lined Heat Shrink Tubing 3:1 Ratio
Your Rating
Products you might like!
Adhesive Lined Heat Shrink Tubing 3:1 Ratio Cut pieces
Adhesive Lined Heat Shrink Tubing 3:1 Ratio Cut pieces
$25.00